Omnitron iConverter 10/100M2 - Fiber media converter - Ethernet, Fast Ethernet - 10Base-T, 100Base-FX, 100Base-TX - RJ-45 / SC single-mode - up to 37.3 miles - 1310 nmItem#: 13526690 | Model#: 8903N-2
- Temporarily out of stock. Order today and we'll deliver when available. (Details)
Omnitron iConverter 10/100M2 - fiber media Product Details
The 10/100M2 utilizes the iConverter Operations, Administration and Maintenance (OAM) management system to remotely monitor network status, configure hardware parameters, generate statistic reports and receive a variety of user-specified traps. The iConverter management system reduces operational expenditures by keeping "truck rolls" to a minimum through remote provisioning and instant trap notification capabilities.
The iConverter 10/100M2 supports Port Access, enhanced Bandwidth Control, Port MIB statistics, 2,048 byte frames and Layer 2 Control Protocol (L2CP) Policy Control.
The 10/100M2 features multiple, user-selectable link fault detection modes for quick fault detection and isolation. These modes operate independently of the network management and monitor the state of the cabling hardware:
Link-Segmentation (LS): The normal (default) mode where the UTP and fiber ports establish their links to other connected devices independently of each other.
Link-Propagation (LP): In this mode (also known as "Link-Loss-Carry-Forward"), a link-out from the UTP port is generated only when a link-in to the fiber port is present, and a link-out from the fiber port is generated only when a link-in to the UTP port is present. In LP mode, a cable or link fault is propagated in a "domino" fashion to downstream or upstream connected equipment, enabling rapid fault detection.
Asymmetrical Link Propagation (ALP): ALP has two modes of operation: copper-to-fiber and fiber-to-copper. In the 'copper-to-fiber' mode, a fault on the UTP port will propagate across the fiber to attached link partner, but not to the UTP port of the link partner. A fault on the fiber will not propagate at all. In the 'fiber-to-copper' mode, a fault on the UTP port will not propagate through to the attached UTP device. In this mode the "domino" effect is limited.
Remote-Fault-Detection (RFD): In RFD+LS mode, each port transmits a link signal only when receiving a link. As a result, link faults (no link received) are looped-back and can be reported to the network core
Remote Fault Detection + Link Propagate (RFD+LP): In RFD+LP mode, link faults are propagated from the fiber to the UTP port and also looped-back to the fiber port. This mode provides rapid reporting of any cable faults to the network core.
Symmetrical-Fault-Detection (SFD): SFD mode is similar to the RFD mode and provides a loop-back of a fiber link fault. When connecting two SFD configured converters "back-to-back", this mode facilitates fiber or UTP fault notification to both ends of the network.
Device Type: Fiber media converter
Form Factor: Plug-in module
Connectivity Technology: Wired
Cabling Type: 10Base-T, 100Base-FX, 100Base-TX
Data Link Protocol: Ethernet, Fast Ethernet
Data Transfer Rate: 100 Mbps
Optical Wave Length: 1310 nm
Remote Management Protocol: SNMP, Telnet
Max Transfer Distance: 37.3 miles
Status Indicators: Link activity, link OK, status
Features: Full duplex capability, auto-negotiation, VLAN support, manageable, Quality of Service (QoS), Remote-Fault-Detection (RFD), Link-Propagation (LP), Link-Segmentation (LS)
Compliant Standards: IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1ad, IEEE 802.3ah
Expansion / Connectivity
Interfaces: 1 x Ethernet 10Base-T/100Base-TX - RJ-45 female ¦ 1 x Ethernet 100Base-FX - SC single-mode female x 2 ¦ 1 x RS-232 ( management ) - 6 pin mini-DIN female
Compatible Slots: 1 x expansion slot
Cables Included: 1 x serial cable
MTBF: 600,000 hours
Compliant Standards: FCC Class B certified, UL
Dimensions & Weight
Width: 0.9 in
Depth: 4.6 in
Height: 3.4 in
Weight: 8.01 oz
Service & Support: Limited warranty - lifetime
Min Operating Temperature: 32 °F
Max Operating Temperature: 122 °F
Manufactured by: Omnitron Systems
Warranty provided by: Omnitron Systems
UPC No: 0800975024625
Mfg Part No: 8903N-2
( Length:0, Width:0, Depth:0)
Shipping Weight: 1.0000 pound(s)
Click here for full warranty and support information
- Omnitron Systems logos are registered trademarks of Omnitron Systems. All others trademarks and copyrights mentioned herein are the property of their respective owners.