Omnitron iConverter 10/100M2 - fiber media
Price: $68399 Free shipping Today!
ADD TO CART
Omnitron iConverter 10/100M2 - fiber media
  1. ADD TO CART
  2. Save to wishlist

Omnitron iConverter 10/100M2 - Fiber media converter - Fast Ethernet - 10Base-T, 100Base-FX, 100Base-TX - RJ-45 / ST single-mode - up to 18.6 miles - 1310 nm

Item#:  8010413  | Model#: 8901N-1-W
Price:
$683.99
Free Shipping Today!
Shipping:
Temporarily out of stock. Order today and we'll deliver when available. (Details)

Omnitron iConverter 10/100M2 - fiber media Product Details

The 10/100M2 utilizes the iConverter Operations, Administration and Maintenance (OAM) management system to remotely monitor network status, configure hardware parameters, generate statistic reports and receive a variety of user-specified traps. The iConverter management system reduces operational expenditures by keeping "truck rolls" to a minimum through remote provisioning and instant trap notification capabilities.

The iConverter 10/100M2 supports port access, enhanced bandwidth control, port MIB statistics, 2,048 byte frames and layer 2 control protocol (L2CP) policy control.

The 10/100M2 features multiple, user-selectable link fault detection modes for quick fault detection and isolation. These modes operate independently of the network management and monitor the state of the cabling hardware:

Link-Segmentation (LS): the normal (default) mode where the UTP and fiber ports establish their links to other connected devices independently of each other.

Link-Propagation (LP): in this mode (also known as "Link-Loss-Carry-Forward"), a link-out from the UTP port is generated only when a link-in to the fiber port is present, and a link-out from the fiber port is generated only when a link-in to the UTP port is present. In LP mode, a cable or link fault is propagated in a "domino" fashion to downstream or upstream connected equipment, enabling rapid fault detection.

Asymmetrical Link Propagation (ALP): ALP has two modes of operation: copper-to-fiber and fiber-to-copper. In the 'copper-to-fiber' mode, a fault on the UTP port will propagate across the fiber to attached link partner, but not to the UTP port of the link partner. A fault on the fiber will not propagate at all. In the 'fiber-to-copper' mode, a fault on the UTP port will not propagate through to the attached UTP device. In this mode the "domino" effect is limited.

Remote-Fault-Detection (RFD): in RFD+LS mode, each port transmits a link signal only when receiving a link. As a result, link faults (no link received) are looped-back and can be reported to the network core

Remote Fault Detection + Link Propagate (RFD+LP): in RFD+LP mode, link faults are propagated from the fiber to the UTP port and also looped-back to the fiber port. This mode provides rapid reporting of any cable faults to the network core.

Symmetrical-Fault-Detection (SFD): SFD mode is similar to the RFD mode and provides a loop-back of a fiber link fault. When connecting two SFD configured converters "back-to-back", this mode facilitates fiber or UTP fault notification to both ends of the network.

Specifications

General
   Device Type:  Fiber media converter
   Form Factor:  Plug-in module

Networking
   Connectivity Technology:  Wired
   Cabling Type:  10Base-T, 100Base-FX, 100Base-TX
   Data Link Protocol:  Ethernet, Fast Ethernet
   Data Transfer Rate:  100 Mbps
   Optical Wave Length:  1310 nm
   Remote Management Protocol:  SNMP, Telnet
   Max Transfer Distance:  18.6 miles
   Status Indicators:  Link OK, status, link/activity
   Features:  Full duplex capability, auto-negotiation, VLAN support, manageable, Quality of Service (QoS), Remote-Fault-Detection (RFD), Link-Propagation (LP), Link-Segmentation (LS)
   Compliant Standards:  IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1ad, IEEE 802.3ah

Expansion / Connectivity
   Interfaces:  1 x Ethernet 10Base-T/100Base-TX - RJ-45 female ¦ 1 x Ethernet 100Base-FX - ST single-mode female x 2 ¦ 1 x RS-232 (management) - 6 pin mini-DIN female
   Compatible Slots:  1 x expansion slot

Miscellaneous
   Cables Included:  1 x serial cable
   MTBF:  600,000 hours
   Compliant Standards:  FCC Class B certified, UL

Dimensions & Weight
   Width:  0.9 in
   Depth:  4.6 in
   Height:  3.4 in
   Weight:  8.01 oz

Manufacturer Warranty
   Service & Support:  Limited warranty - lifetime

Environmental Parameters
   Min Operating Temperature:  -40 °F
   Max Operating Temperature:  140 °F
 
  • Manufactured by: Omnitron Systems
    Warranty provided by: Omnitron Systems
    UPC No: 788597002590
    Mfg Part No: 8901N-1-W
  • Box Size: ( Length:0, Width:0, Depth:0)
    Shipping Weight: 1.0000 pound(s)
    Click here for full warranty and support information
  • Omnitron Systems logos are registered trademarks of Omnitron Systems. All others trademarks and copyrights mentioned herein are the property of their respective owners.
Plus get insider deals first, exclusive promotions and more!
 
Sponsored by: