Omnitron iConverter 10/100M2 - fiber media
Price: $50899
ADD TO CART
Omnitron iConverter 10/100M2 - fiber media
  1. ADD TO CART
  2. Save to wishlist

Omnitron iConverter 10/100M2 - Fiber media converter - Ethernet, Fast Ethernet - 10Base-T, 100Base-FX, 100Base-TX - RJ-45 / SC multi-mode - up to 3.1 miles - 1310 nm

Item#:  40165750  | Model#: 8902N-0-EW
Price:
$508.99
Shipping:
Temporarily out of stock. Order today and we'll deliver when available. (Details)

Omnitron iConverter 10/100M2 - fiber media Product Details

The iConverter 10/100M2 Network Interface Device (NID) media converter provides 10Base-T or 100Base-Tx (10/100) to 100Base-Fx Fiber media conversion with integrated management. The 10/100M2 conforms to Ethernet in the First Mile (EFM) fiber standards to support Fiber-to-the-X (FTTX) Metropolitan and Enterprise LAN networks. 10/100M2 media converters are used to provide managed copper demarcation points at the customer premises and network edge, offering Quality of Service and Bandwidth Control (rate-limiting) capabilities.

The 10/100M2 utilizes the iConverter Operations, Administration and Maintenance (OAM) management system to remotely monitor network status, configure hardware parameters, generate statistic reports and receive a variety of user-specified traps. The iConverter management system reduces operational expenditures by keeping "truck rolls" to a minimum through remote provisioning and instant trap notification capabilities.

The iConverter 10/100M2 supports Port Access, enhanced Bandwidth Control, Port MIB statistics, 2,048 byte frames and Layer 2 Control Protocol (L2CP) Policy Control.

The 10/100M2 features multiple, user-selectable link fault detection modes for quick fault detection and isolation. These modes operate independently of the network management and monitor the state of the cabling hardware:

Link-Segmentation (LS): The normal (default) mode where the UTP and fiber ports establish their links to other connected devices independently of each other.

Link-Propagation (LP): In this mode (also known as "Link-Loss-Carry-Forward"), a link-out from the UTP port is generated only when a link-in to the fiber port is present, and a link-out from the fiber port is generated only when a link-in to the UTP port is present. In LP mode, a cable or link fault is propagated in a "domino" fashion to downstream or upstream connected equipment, enabling rapid fault detection.

Asymmetrical Link Propagation (ALP): ALP has two modes of operation: copper-to-fiber and fiber-to-copper. In the 'copper-to-fiber' mode, a fault on the UTP port will propagate across the fiber to attached link partner, but not to the UTP port of the link partner. A fault on the fiber will not propagate at all. In the 'fiber-to-copper' mode, a fault on the UTP port will not propagate through to the attached UTP device. In this mode the "domino" effect is limited.

Remote-Fault-Detection (RFD): In RFD+LS mode, each port transmits a link signal only when receiving a link. As a result, link faults (no link received) are looped-back and can be reported to the network core

Remote Fault Detection + Link Propagate (RFD+LP): In RFD+LP mode, link faults are propagated from the fiber to the UTP port and also looped-back to the fiber port. This mode provides rapid reporting of any cable faults to the network core.

Symmetrical-Fault-Detection (SFD): SFD mode is similar to the RFD mode and provides a loop-back of a fiber link fault. When connecting two SFD configured converters "back-to-back", this mode facilitates fiber or UTP fault notification to both ends of the network.

Specifications

General
   Device Type:  Fiber media converter
   Form Factor:  External

Networking
   Connectivity Technology:  Wired
   Cabling Type:  10Base-T, 100Base-FX, 100Base-TX
   Data Link Protocol:  Ethernet, Fast Ethernet
   Data Transfer Rate:  100 Mbps
   Optical Wave Length:  1310 nm
   Remote Management Protocol:  SNMP, Telnet
   Max Transfer Distance:  3.1 miles
   Status Indicators:  Link activity, link OK, status
   Features:  Full duplex capability, auto-negotiation, VLAN support, manageable, wall mountable, Quality of Service (QoS), Remote-Fault-Detection (RFD), Link-Propagation (LP), Link-Segmentation (LS)
   Compliant Standards:  IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1ad, IEEE 802.3ah

Expansion / Connectivity
   Interfaces:  1 x Ethernet 10Base-T/100Base-TX - RJ-45 female ¦ 1 x Ethernet 100Base-FX - SC multi-mode female x 2 ¦ 1 x RS-232 ( management ) - 6 pin mini-DIN female

Miscellaneous
   Cables Included:  1 x serial cable
   Compliant Standards:  FCC Class B certified, UL

Power
   Power Device:  External power adapter
   Voltage Required:  AC 120/230 V ( 50/60 Hz )

Dimensions & Weight
   Width:  3.8 in
   Depth:  4.7 in
   Height:  1 in
   Weight:  16.01 oz

Manufacturer Warranty
   Service & Support:  Limited lifetime warranty
   Service & Support Details:  Limited warranty - lifetime

Environmental Parameters
   Min Operating Temperature:  -40 °F
   Max Operating Temperature:  140 °F
 
  • Manufactured by: Omnitron Systems
    Warranty provided by: Omnitron Systems
    UPC No: 0800975033726
    Mfg Part No: 8902N-0-EW
  • Box Size: ( Length:0, Width:0, Depth:0)
    Shipping Weight: 2.0000 pound(s)
    Click here for full warranty and support information
  • Omnitron Systems logos are registered trademarks of Omnitron Systems. All others trademarks and copyrights mentioned herein are the property of their respective owners.