Full Compass Electro-Voice RE-20 Dynamic Cardioid Product Details
The RE20’s bass roll-off switch and EV’s Variable-D technology ensures true and accurate response across all frequencies without the up-close boominess associated with proximity effect. It gives the same response at varying distances.
Variable-D® designed microphones, like the RE20, can be used very close to other sound sources with no loss in clarity or definition. This makes them the preferred choice for tight vocals and challenging instruments such as brass.
A true cardioid microphone, the RE20 offers greatest rejection at 180º off axis - directly to the rear of the microphone. Pattern control is so consistent that the frequency response is nearly independent of angular location of the sound source, creating virtually no off-axis coloration, yet providing greatest possible rejection of unwanted sounds.
An integral blast and wind filter covers each acoustic opening on the RE20. In recording sessions or on stage, singers can “close talk” the microphone, singing with their lips almost touching the grille screen with no worry of “P-pops” or excessive sibilance. Part of the filter also shock mounts the internal microphone element, reducing the transfer of vibrations from external sources.
The exceptional performance of the RE20 is achieved by using a large Acoustalloy diaphragm in combination with an exceptionally low-mass aluminum voice coil. Using this diaphragm assembly, the RE20 is capable of reproducing extremely high sound pressure levels with no fear of the overload and distortion often experienced with phantompowered condensers.
The RE20 will continue to function flawlessly in high humidity and elevated temperatures that would seriously degrade competitive condenser microphones.
A massive steel housing and effective hum-bucking coil assure the RE20’s resistance to magnetically induced hum and noise. This means the RE20 can be used successfully in situations where other microphones would experience unacceptable levels of hum and buzz. By exploiting the strength of its steel housing and employing a mechanical nesting concept, EV designers have created an exceptionally rugged microphone with superior handling noise rejection ideally suited for professional uses.
The bass-boosting proximity effect common to most directional microphones when used close to the sound source, is eliminated in the RE20. This is accomplished via the application of the EVexclusive Variable-D® technology. By controlling the effect of microphone proximity, the RE20 can be located very close to sound sources without a loss in clarity or definition making the RE20 ideal for tight vocals and challenging instruments. It can be used inside bass drums, on acoustic guitars, and is found in voice booths and broadcasting studios everywhere.
The microphone is a cardioid type with an integral blast filter protecting all acoustic openings. The blast filter serves as a shock mount for the internal microphone element. The microphone has a wide-range uniform frequency response from 45-18,000 Hz. An integral passive network is provided so that when the filter switch is in the “on” position, low-frequency response shall tilt down 4.5 dB from 400-100 Hz. With switch in “off” position, microphone is essentially “flat” from 80-6,000 Hz, with a broad 2.5 dB rise in response from 6,000-14,000 Hz, and nominally down3 dB at 18,000 Hz.
Response below 80 Hz is nominally down 3 dB at 45 Hz. Output level is -57 dB (0 dB = 1 mW/Pascal). Nominal impedance of 150 ohms. Response at any angular position away from the major axis is essentially similar to the response on the major axis, but attenuated uniformly at all frequencies by an amount appropriate to that angular position.
Attenuation at frequencies from 45-10,000 Hz (refer to major axis signal value) exceeds 15 dB at 180° from major axis in any plane. Attenuation above 10,000 Hz exceeds 13 dB. Polar characteristics are sufficiently uniform in all planes so that it is, effectively, a cardioid of revolution. This microphone has a shield to prevent dust and iron particles from reaching the diaphragm. The case is made of steel. The microphone has a diameter of 54.4 mm (2.14 in.), a body diameter of 49.2 mm (1.94 in.) and a length of 216.7 mm (8.53 in.). A stand adapter is supplied.
>>Variable-D® dynamic cardioid microphone
>>Favorite among broadcasters and engineers worldwide
>>Variable-D® design and heavy-duty, internal P-pop filter reduces proximity effect
>>Internal element shock mount reduces vibration-induced noise
>>Bass roll-off switch
>> Generating Element: Dynamic
>>Frequency Response: 45-18,000 Hz
>>Polar Pattern: Cardioid
>>Impedance: 150 ohms balanced
>>Sensitivity, Open Circuit Voltage: 1.5 mV/Pascal = 1 kHz
>>Power Level, 1 kHz (0 dB = 1 mV/Pascal): -57 dB
>>Hum Pickup Level, typical (60 Hz/1 millioersted field): -130 dBm
>>Polarity: Pin 2 will be positive referenced to Pin 3 with positive pressure on diaphragm
>>Case Material: Steel
>> Length: 216.7 mm (8.53")
>>Widest Diameter: 54.4 mm (2.14")
>>Body Diameter: 49.2 mm (1.94")
Manufactured by: Full Compass
UPC No: 0701001000098
Mfg Part No: RE-20
( Length:12, Width:6, Depth:3)
Shipping Weight: 2.7500 pound(s)
Click here for full warranty and support information
- Full Compass logos are registered trademarks of Full Compass. All others trademarks and copyrights mentioned herein are the property of their respective owners.